|
Halltech 2015-2019 Corvette C7 Z06 Stinger-RZ™
|
|
Halltech 2014-2019 C7 Stingray LT1
|
(1)
|
|
|
(1)
|
|
|
|
|
Halltech's 2015 Corvette C7 Z06 Stinger-RZ will put you in the winner's circle. 1/4 mile e.t. improvement= .41 seconds; 1/4 mile trap speed improvement=6 mph! Dyno tests have shown between 38 and 52 RWHP with no tuning. Two recent dynos at A&A Corvette (91 Octane-A8s) reported 44 RWHP/41 lb-ft and 50 RWHP and 43 lb-ft with the stock ECM parameters, i.e. no tuning. The ST689 filter is installed on all orders. Our dry filter is optional (ST589) Our Nomex Sock heat shielding is optional for $45.00 (product code Nomex). Just in: Halltech's Stinger-RZ runs a 10.77 @ 128 mph! Our customer previously ran an 11.16 @ 122 mph showroom stock. The DA was 2400' on the before and after 1/4 mile pass.
|
Halltech's 2014-2020 Corvette Stingray (and Grand Sport) cold air intake. Please determine how many PCV lines in your application. GM started using 1 PCV in 2017, but we see many 17s-19s with two PCV lines. This is critical information to avoid returns. All systems now ship with our new dry nano filter, private labeled exclusively for Halltech by TKO (makers of the Attack Blue filter). NOTE: the f-panel seal referenced in the installation video is not needed and is thus no longer provided in the kit (you can ignore this step in the instructions). Halltech does not have a CA EO number for this induction system, which means it is not legal for sale in CA, unless used in off-road application, such as track racing. |
|
|
|
Halltech C6 Venom™(2005-2007 LS2) includes Beehive Heat Shield
|
|
HALLTECH TRIC RAM AIR INDUCTION SYSTEM (C7 Z06 & Grand Sport ONLY)
|
(1)
|
|
|
|
|
|
Halltech C6 Venom™ II is the direct replacement for the stock LS2 intake box. Bolt on 15 RWHP/12 lbs ft torque with our all new design. Now with a larger 106.7mm inlet and built in velocity stack, no other bolt on will make more power. This intake is made from the same mold as the Killer Bee™ II that dynoed +15 HP/+14lbs-ft. on the Katech Engine Development Superflow dyno. The same huge high flow Attack Blue Filter will flow over 1250 cfm, and feeds over 900 HP easily. This system uses the stock wiring, and MAF sensor for direct bolt on power that will not void your warranty. The Halltech Beehive is included in our pricing. We now include our HC.125 honeycomb flow straightener with your purchase. No tuning required. MAF sensor not included.
We do not recommend cutting any holes in your radiator shroud (in an attempt to get more air to the filter). It is not necessary, and will cause lean codes and surging.
All systems now ship with our new dry nano filter, private labeled exclusively for Halltech by TKO (makers of the Attack Blue filter).
Halltech does not have a CA EO number for this induction system, which means it is not legal for sale in CA, unless used in off-road application, such as track racing.
|
HALLTECH TRIC RAM AIR INDUCTION SYSTEM (C7 Z06 & Grand Sport ONLY) DO NOT USE DURING RAIN-DO NOT TAKE YOUR CAR THROUGH CAR WASHES.
This is the best modification you can add to your C7 Z06 to increase boost, thereby increasing horsepower. Preliminary track testing has shown that at 88 mph in second gear, you can expect 11.4 PSI boost and at 124 mph 12.1 PSI boost (Intake Air Temps are in parity with Ambient ). This is due in part to the high flow filter utilized on our Stinger-RZ, worth 50 RWHP on its own. The TRIC brings huge volumes of cold dense air directly into the F-panel cavity where otherwise the stock system uses vacuum to draw air from the bottom of the front end. We effectively steal the airflow that the factory directs at the front right rotor for road racing. By drilling a few holes, our TRIC system will allow you to still utilize that airflow, but it will divert a large amount of the airflow into the airbox. For high boost application, we would keep the rotor duct blocked off. We have not tested this system in road racing yet to see the effect of this airflow diversion on the right rotor cooling, so if you road race, you might want to pass on this mod. Rain is an absolute no with ram air systems. If you live in areas where it rains a lot. Just pass on this mod. Car Washes have the same issues.
Some stats: IAT 1 runs in parity with the Ambient temps most of the time. degrees more than ambient. IAT2 +15 degrees. Very minimal knock retard was seen in our testing, even at 12.1 PSI at 125 mph. Our Z06 is completely stock, using pump 93 Octane, and has 7000 miles on our Stinger-RZ.
|
|
|
|
Halltech C6 DRED Hood pre-order list
|
|
Halltech Black Killer Bee™ MF103
|
|
|
(2)
|
|
|
|
|
|
"Purchase" this $0 item to get on the official preorder list
Resurrection of the Halltech DRED Hood.
- This hood is made from primered/paintable carbon fiber outer skin and prepreg clear bottom.
It features the same type of Direct Radiator Exit Design as seen in the C6-R Pratt and Miller Specialty C6 Corvette as seen in the accompanying picture. The Blue Halltech C6 ULZ750 is the configuration we are starting with, but once production starts, we might have different configurations. In May we are making one hood, which is already dedicated to a customer, but only after we do our due diligence, and have acceptance from this individual.
No deposit required at this time, but ordering will give us an idea of the commitment we need to make to our vendor.
|
The MF103 is our Plug and Play induction system for the LS3 and LS7. It is designed to require no additional tuning, but if you tune your car, expect 31 to 35 RWHP total with the MF103R.
|
|
|
PEOPLE TRUST 
"This is my first mod to any of my Z06's. The filter feels great. Feels better when running thru
gears at part gas."
- DALE P.
"It ran like a different car at wide open throttle, the SOTP meter was off the charts, it feels like
a 100 shot of
nitrous. For the money, it's a bargain"
- WALTER S.
"I've upgrade my car's ECM with the tuned file (stock filter) that you've sent; and let me tell you
the car gone "mad"!!
... Seriously the feeling is brutal and I love it."
YOUSUF H.
|
